Detail
- VANTAGE is applicable to all types of horizontal injection machine of 50~450T for take-out products. The installation direction is different from traditional beam robot, products and sprues are placed at the end of IMM. It has single stage and telescopic type; It can be added a sub-arm for 3-plates mold to grip products and sprue at the same time, vertical stroke: 600-1000mm.
- Install VANTAGE robot can save 30~40% room to allow better utilization of production space; Furthermore, the productivity will be increased 20~30%, reduce defective rate, ensure safety of operators, reduce manpower and accurately control the output to reduce waste.
- Structure：
- AC servo motor driven on traverse axle, vertical and Crosswise driven by pneumatic cylinder. Traverse axle , crosswise and vertical arm are applied with advanced high rigidity linear slide rail, and light high rigidity alloy aluminum extrusion beam for crosswise and vertical axles to integrating with linear slide rail, it works with high speed, high efficiency, low vibration, and long use life.
- Telescopic type with special double-speed belt structure quicken vertical speed, it can be applicable to low workshop.
- Optional Function:
- Crosswise/Vertical remote adjustment: Position adjusted by remote control, saved adjustment time and enhanced safety of operation.
- Spraying device: spraying number of molds and spraying time of each spray can be set. The nozzle can be installed on the arm or mould. Up to two groups of settings.
- Middle mold Inspection: Detecting position of the middle mold platen of 3-plates mold.
- Photoelectric inspection on finished products: Placing products on the conveyor, so as to avoid hitting each other.
- Air Nipper: It can be installed on the arm or at the end of traverse for cutting sprue.
- CE connectors: EUROMAP 12 standard connector is available.
- Control System:
- Control box integrated with robot to save space. Palm controller with user-friendly interactive interface. Exchangeable English/Chinese display. Built-in programs for free selection and combination. Automatically defecting and recording the failures. Twenty groups of molding memorizing function. With L/U type take-out mode is selectable. Able to take out from fixed-mould side matched with different swivel actions. Different placing mode (traverse-out, traverse-in, out-mould simultaneous placing) are available. All the Timer and Counter can be changed under AUTO MODE .Modular PC board design, easy to maintain and replace. Compliance with CE standard.
Feature
Specification
General specification:
| Power source |
Working pressure |
Max. allowed pressure |
Drive system |
Swivel |
Control system |
3øAC220v±10v
50/60HZ |
5kgf/cm2
0.49Mpa |
8kgf/cm2
0.8Mpa |
Y AC servo motor
X,Z pneumatic cylinder |
90°Fixed
Pneumatic |
HA80 |
Main specification:
| Model |
VA600
ID/IS/WD/WS |
VA800
ID/IS/WD/WS |
VA1000
WD/WS |
| Power capacity(KVA) |
1 |
1 |
1.5 |
| Recommended IMM(ton) |
50-150 |
100-250 |
250-450 |
| Traverse Stroke(mm) |
2000(2500) |
3000(3500) |
4000(4500) |
| Crosswise Stroke(mm) |
P:150 R:100 |
P:300 R:100 |
P:400 R:100 |
| Vertical Stroke(mm) |
600(750) |
850(950) |
1050(1150) |
| Max. loading(kg) |
5 |
5 |
8 |
| Dry take out Time(sec) |
2 |
2.2 |
2.5 |
| Dry cycle Time(sec) |
8 |
10 |
12 |
| Air consumption(NI/cycle) |
21 |
23 |
25 |
| Net weight(kg) |
260-280 |
320-350 |
380-420 |
Denote: ″P″: product arm ″R″: runner arm I: single stage W: telescopic type D: product arm + runner arm S: product arm A: remote adjustment of crosswise axis G: remote adjustment of vertical axis
